Privileges: SUBSYSTEM-MANAGEMENT
Function
The administration information on supply units not needed anymore can be deleted from the open SCI with the REMOVE-SUPPLY-UNITS statement. Supply units in the “Parked” or “Installed” installation state cannot be deleted.
Format
REMOVE-INSTALLATION-UNITS | |||||||||||||||||||||||||
| |||||||||||||||||||||||||
Operands
UNIT-NAME =
Selection of the supply units to be deleted.
UNIT-NAME = *BY-DIALOG
The supply units can be listed in a selection window and selected in an interactive dialog (see "Interactive selection of supply units"). Interactive selection is not available in the batch mode.
UNIT-NAME = list-poss(30): <text 1..30 without-sep>(...)
Name of the supply unit, see "Installation unit (IU) ". Up to 30 supply units can be specified in a list.
VERSION =
Version of the supply unit.
VERSION = *HIGHEST-EXISTING
The highest version of the supply unit will be used.
VERSION = *LOWEST-EXISTING
The lowest version of the supply unit will be used.
VERSION = *ALL
All versions of the supply unit will be used.
VERSION = <product-version 3..7 without-man>
Version designation without the release and correction status.
CORRECTION-STATE =
Correction state of the supply unit.
CORRECTION-STATE = *HIGHEST-EXISTING
The highest correction state of the supply unit will be used.
CORRECTION-STATE = *LOWEST-EXISTING
The lowest correction state of the supply unit will be used.
CORRECTION-STATE = *ALL
All correction states of the supply unit will be used.
CORRECTION-STATE = list-poss(15): <alphanum-name 3..3>
The correction state of the supply unit is specified explicitly.
Format: <aso>
Notes
In the following cases the statement is rejected without taking any action and an error
message is output:
The SCI cannot be accessed with write privileges.
The value *BY-DIALOG was specified in the batch mode.
The SCI does not contain the specified supply units.
There are double supply unit entries in the input list, i.e. supply units with the same values or keywords for one of the identification parameters.
One of the selected supply units is in the “Installed” or “Parked” state.
The selection criteria are applied to the specified supply units. When using the corresponding keywords, it is recommended to issue a SHOW statement with the same criteria beforehand as a check.
Interactive selection of supply units
If the operand value UNIT-NAME=*BY-DIALOG is entered in the REMOVE-SUPPLY-UNITS statement, then a selection window appears. Additional supply units are selected interactively in a dialog. The supply units are interactively selected by entering any character in front of the desired supply unit.
IMON: SCI: :I29A:$TSOS.SYS.IMON.SCI
------------------------------------------------------------------------------
Units 1 through 13 of 168
SU selection More: +
Unit name Vers Corr Package name User code Inst. Status CAP Act
ACS 21.0 A00 <package-name> SOL2P Installed N Y
AID 03.5 A00 <package-name> SOL2P Installed N Y
AIDSYS 21.0 A00 <package-name> SOL2P Installed N Y
AIDSYSA 21.0 A00 <package-name> SOL2P Installed N Y
ANITA 21.0 A00 <package-name> SOL2P Installed N Y
APACHE 02.4 A00 <package-name> SOL2P Installed N Y
ARCHIVE 12.0 C00 <package-name> SOL2P Installed N Y
ASE 21.0 A00 <package-name> SOL2P Installed N Y
ASSEMBH 01.4 A10 <package-name> SOL2P Installed N Y
ASSEMBH-GEN 01.4 A10 <package-name> SOL2P Installed N Y
ASSTRAN 05.4 A00 <package-name> SOL2P Installed N Y
ASTI 21.0 A00 <package-name> SOL2P Installed N Y
ATS 05.3 A20 <package-name> SOL2P Installed N Y
------------------------------------------------------------------------------
Command ==>
F1=Help F3=Exit F5=Previous F6=Next F7=Backward F8=Forward F10=Menu ...
Figure 60: Interactive selection of supply units
Notes
After the supply units have been selected, the selection process and the window are terminated with [DUE]. The user is then back in IMON’s SDF interface and additional IMON statements can be entered.
Interactive selection is not available in the batch mode.