Your Browser is not longer supported

Please use Google Chrome, Mozilla Firefox or Microsoft Edge to view the page correctly
Loading...

{{viewport.spaceProperty.prod}}

Example of DIALOG startup

&pagelevel(4)&pagelevel

The following example illustrates the stages in a DIALOG startup (in extracts) on an SU /390. It corresponds to the logging in the CONSLOG file (partially abbreviated); the message sequence output at the console may differ from the sequence given below.

TCLOG    .125439  ***2021-01-25*** 000001 **** UTC+01:00 
****************************************************************
(C0) %   P-000.125439 NSI00E3 IPL-REPS READ: 1; EXECUTED: 1
(C0) %   P-000.125439 NSI1100 IPL DEVICE = MH20.0; IPL PATH = BE18 (MN=BE18)
(C0) %   P-000.125439 NSI1106 *** BS2000 DIALOGUE STARTUP ***
(C0) ?   P-000.125439 NSI1110 ENTER OPTIONS OR EOT. REPLY (UNLOCK,TEST,ALLDISK,DRV-SELECT,CREATE-DRV,IPL-CONF)
   P R(C0)-000.125439. 
-----------------------------------------------------------------------------------------  1.
(C0) %   P-000.125439 NSI3135 IPL DISK-SETUP READ FROM IPL-CONF PREPARED 2021-01-12 13:29:55
(C0) %   P-000.125439 NSI1143 002 PUBVOLS OF HOME-PVS MH20 WITH SYSID 117 ONLINE 
-----------------------------------------------------------------------------------------  2.
(C0) %   P-000.125439 NSI1145 MH20.0 2021-01-25 12:53:37 ON BE18 
(C0) %   P-000.125439 NSI1145 MH20.1 2021-01-25 12:53:37 ON BE19 
(C0) %   P-000.125439 NSI1153 STATE OF PROCESSORS ONLINE:
(C0) %   P-000.125439 NSI1155 CPU 00 ONLINE, ATTACHED (IPL CPU)
(C0) %   P-000.125439 NSI1158 CPU 01 ONLINE, DETACHED
(C0) %   P-000.125439 NSI1163 LOCAL DATE = 2021-01-25, TIME = 12:53:52 FROM SVP 
-----------------------------------------------------------------------------------------  3.
(C0) %   P-000.125439 NSI1180 LOAD ADDRESS OF SYSPRG.STRT.210 = 00777000
(C0) %   P-000.125439 NSI00E6 SYSREP.STRT.210 IS USED AS REP FILENAME 
-----------------------------------------------------------------------------------------  4.
(C0) ?   P-000.125439 NSI0050 SPECIFY PARAM FILE OR DEVICE. 
                      REPLY (EOT (USE STANDARD FILE);FN=FILENAME(,VOL=VSN);CONS;END)
   P R(C0)-000.125439. 
-----------------------------------------------------------------------------------------  5.
(C0) %   P-000.125439 NSI00E6 SYSPAR.BS2.210.VM07S700 IS USED AS PARAM FILENAME
(C0) %   P-000.125439 NSI006B FILE SYSPAR.BS2.210.VM07S700 NOT FOUND
(C0) %   P-000.125439 NSI00BC LAST PARAM FILE/DEVICE IGNORED
(C0) %   P-000.125439 NSI00E6 SYSPAR.BS2.210 IS USED AS PARAM FILENAME
(C0) ?   P-000.125439 NSI0050 SPECIFY PARAM FILE OR DEVICE. 
                      REPLY (EOT (USE STANDARD FILE);FN=FILENAME(,VOL=VSN);CONS;END)
   P R(C0)-000.125439.END 
-----------------------------------------------------------------------------------------  6.
(C0) ?   P-000.125439 NSI1190 ENTER BS2000-FILENAME. REPLY (FILENAME(,VOL=VSN); EOT (USE STANDARD FILE))
   P R(C0)-000.125439. 
-----------------------------------------------------------------------------------------  7.
(C0) ?   P-000.125439 NSI0050 SPECIFY BS2000 REP FILE OR DEVICE. 
                      REPLY (EOT (USE STANDARD FILE);FN=FILENAME(,VOL=VSN);CONS;END)
   P R(C0)-000.125439. 
-----------------------------------------------------------------------------------------  8.
(C0) %   P-000.125439 NSI00E6 SYSREP.BS2.210 IS USED AS REP FILENAME
(C0) ?   P-000.125439 NSI0050 SPECIFY BS2000 REP FILE OR DEVICE. 
                      REPLY (EOT (END); FN=FILENAME(,VOL=VSN);CONS;END)
   P R(C0)-000.125439.END 
-----------------------------------------------------------------------------------------  9.
(C0) %   P-000.125439 NSI0028 AVAILABLE MEMORY = 4.0 GB. CPU = 60029001 26000000 
----------------------------------------------------------------------------------------- 10.
(C0) %   P-000.125439 NSI5103 BS2000 : NAME = G10BXS, VERSION = 21.0A00, GEN-TIME = 2020-10-06 17:34:20
(C0) %   P-000.125439 NSI5102 COPYRIGHT (C) 2021 FUJITSU TECHNOLOGY SOLUTIONS GMBH. ALL RIGHTS RESERVED
(C0) %   P-000.125439 EMM2960 EFFECTIVE SYSSIZE VALUE IS 240 MB
(C0) %   P-000.125439 NSI5150 CPU'S ONLINE: 2  CPU'S INSTALLED: 2
(C0) %   P-000.125439 ETMGT10 GTIME-VALUES FOR SESSION: ZONE=+01:00, DIFF=1:00
(C0) %   P-000.125439 ETMGT01 TODR-EPOCH FOR SESSION: EPOCH=00
(C0) %   P-000.125439 NSI3130 IPL-CONF SAVED ONTO DISK MN=BE18 WITHOUT ERRORS
(C0) %   P-000.125439 NSI5104 IOCF: NAME = SU700001EM-2 29001 26 , 10.10.2020 GEN-TIME = 2021-01-10 11:04:17
(C0) %   E-000.125439 EMM2301 PAGING AREA ON VOLUME MH20.0 SIZE = 02560.00 MB.
(C0) %   E-000.125439 EMM2301 PAGING AREA ON VOLUME MH20.1 SIZE = 02560.00 MB.
(C0) %   E-000.125439 EMM2850 THE SIZE OF THE PAGING-AREA IS 0005120.00 MB; 
                      THE RESERVED SIZE OF THE PAGING-AREA IS 0000011.48 MB.
(C0) %   P-000.125439 NSI6102 BS2000 EXECUTIVE: CLASS2 ACTIVE 
----------------------------------------------------------------------------------------- 11.
(C0) %   P-000.125439 NSI4110 /INPUT DISK F=SYSPAR.BS2.210 
----------------------------------------------------------------------------------------- 12.
(C0) %   P-000.125439 NSI4110 /BEGIN GTIME
(C0) %   P-000.125439 NSI4110 ZONE=+00:00
(C0) %   P-000.125439 NSI4110 DIFF=1:00
(C0) %   P-000.125439 NSI4110 SEASON=S
(C0) %   P-000.125439 NSI4110 EPOCH=00
(C0) %   P-000.125439 NSI4110 CHDATE=1900-01-01/00:00
(C0) %   P-000.125439 NSI4110 CHDATE=1980-03-16/02:00
(C0) %   P-000.125439 NSI4110 CHDATE=1980-10-26/03:00
...
(C0) %   P-000.125439 NSI4110 CHDATE=2024-03-31/01:00
(C0) %   P-000.125439 NSI4110 CHDATE=2024-10-27/02:00
(C0) %   P-000.125439 NSI4110 NEXTZONE
(C0) %   P-000.125439 NSI4110 ZONE=+01:00
(C0) %   P-000.125439 NSI4110 DIFF=1:00
(C0) %   P-000.125439 NSI4110 SEASON=S
(C0) %   P-000.125439 NSI4110 EPOCH=00
(C0) %   P-000.125439 NSI4110 CHDATE=1900-01-01/00:00
(C0) %   P-000.125439 NSI4110 CHDATE=1980-04-06/02:00
(C0) %   P-000.125439 NSI4110 CHDATE=1980-09-28/03:00
...
(C0) %   P-000.125439 NSI4110 CHDATE=2024-03-31/02:00
(C0) %   P-000.125439 NSI4110 CHDATE=2024-10-27/03:00
(C0) %   P-000.125439 NSI4110 NEXTZONE
(C0) %   P-000.125439 NSI4110 /EOF
(C0) %   P-000.125439 NSI4110 /BEGIN OPR
(C0) %   P-000.125439 NSI4110 DEFINE-CONSOLE CONSOLE=C0
(C0) %   P-000.125439 NSI4110 SET-CODE CODE=*ALL,CONSOLE=*IPL
(C0) %   P-000.125439 NSI4110 SET-CODE CODE=*ALL,CONSOLE=(CON1,CON2,CON3,CON4,CON5,CON6,CON7)
(C0) %   P-000.125439 NSI4110 SET-CODE CODE=T,CONSOLE=MARE
(C0) %   P-000.125439 NSI4110 SET-CODE CODE=E,CONSOLE=MARE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE E,ADD-FILE-LINK
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE $,MODIFY-SPACE-SATURATION-LEVELS
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE $,MODIFY-USER-PUBSET-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE $,PRINT-DOCUMENT
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SEVER
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CATJV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,FSTATUS
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-SPOOL-CHARACTER-SETS
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CATM
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-SPOOL-DEVICES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,COPY
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,IMPORT
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-SPOOL-FORMS
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DCLJV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,JOIN
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-SPOOL-PARAMETERS
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ERAJV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-USER-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ERAM
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,PASSWORD
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,STAJV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ERASE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,PRINT
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ADD-MASTER-CATALOG-ENTRY
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,IMPORT-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ADD-PASSWORD
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,LOCK-USER
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,ADD-USER
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-FILE-ATTRIBUTES(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,COPY-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-FILE-GENERATION-SUPPORT
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CREATE-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-FILE-GROUP-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CREATE-FILE-GENERATION
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-JV-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CREATE-FILE-GROUP
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-MASTER-CATALOG-ENTRY
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CREATE-JV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,MODIFY-USER-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,CREATE-TAPE-SET
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,PRINT-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,REMOVE-MASTER-CATALOG-ENTRY
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-FILE-GENERATION
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-FILE-GROUP
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,REMOVE-USER
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-JV
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-FILE-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-TAPE-SET
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-JV-ATTRIBUTES
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,DELETE-SYSTEM-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SET-FILE-LINK
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,EXPORT-FILE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SET-JV-LINK
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,REMOVE-JV-LINK
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-JV-LINK
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,EXTEND-TAPE-SET
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,UNLOCK-USER
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,WRITE-SPOOL-TAPE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,REMOVE-PASSWORD
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,TYPE
(C0) %   P-000.125439 NSI4110 SET-CMD-CODE @,SHOW-LIVE-MIGRATION-HISTORY
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=R,C-N=CMD1,A-N=CON1
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=A,C-N=CMD2,A-N=CON2
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=U,C-N=CMD3,A-N=CON3
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=A,C-N=CMD4,A-N=CON4
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=U,C-N=CMD5,A-N=CON5
(C0) %   P-000.125439 NSI4110 ADD-CMD-ENTRY A-C=R,C-N=CMD6,A-N=CON6
(C0) %   P-000.125439 NSI4110 /EOF
(C0) %   E-000.125439 EMM2310 THE SIZE OF MAIN MEMORY IS 00004096 MB; THE MINIMAL SIZE OF MAIN MEMORY IS 00004096 
MB
(ZA) % UCO-000.125441  %  NBR0706 TEST OUTPUT FOR CONSOLE 'ZA'
...
(C0) % UCO-000.125441  %  NBR0706 TEST OUTPUT FOR CONSOLE 'C0'
  <* % UCO-000.125441  %  EXC0903 CONSOLE 'ZA' INOPERABLE
(C0) % UCO-000.125441  %  EXC0652 CONSOLE 'C0' TAKES OVER ALL FUNCTIONS AND AUTHORIZATIONS OF CONSOLE 'ZA'
...
  <* ? TSC-000.125442 NSI0077 ENTER AUTOMATIC COMMAND FILE NAME. 
                      REPLY (FILE NAME; N(DO NOT USE); EOT(USE STANDARD))
   TSC R(C0)-000.125457. 
----------------------------------------------------------------------------------------- 13.
  <* % UCO-000.125457  %  NBR0792 QUESTION '000' FROM ' TSC' ANSWERED BY '(C0)'. REPLY:  
  <* ?   Q-000.125457  %  NSI6005 SYSTEM PARAMETER STUPTYPE = W. SHALL VALUE BE CHANGED? REPLY ( U(NCHANGED), 
W(ARM),
                          C(OLD), S(ELECTIVE), Z(IP), T(TSN FILE RESET ONLY), J(JOIN AND TSN FILE 
RESET),EOT=UNCHANGED)
   Q R(C0)-000.125500.C 
----------------------------------------------------------------------------------------- 14.
  <* % UCO-000.125500  %  NBR0792 QUESTION '000' FROM '   Q' ANSWERED BY '(C0)'. REPLY: C
  <* ?   Q-000.125500  %  NSI6010 SYSTEM PARAMETER RECONUC = N. SHALL VALUE BE CHANGED? 
                          REPLY ( U(NCHANGED), N(O), B(ACKUP), T(SOSCAT), A(LL), R(ESET), EOT=UNCHANGED
   Q R(C0)-000.125504. N 
----------------------------------------------------------------------------------------- 15.
  <* % UCO-000.125504  %  NBR0792 QUESTION '000' FROM '   Q' ANSWERED BY '(C0)'. REPLY:  
  <* %   Q-000.125504  %  DMS035B IMCAT TASK 'XABW' FOR PUBSET WITH PUBSET ID 'MH20' CREATED AND STARTED
...
  <R %DSSM-000.125504  %  ESM0220 FUNCTION 'CREATE' FOR SUBSYSTEM 'CALENDAR/V21.0' COMPLETELY PROCESSED
...
  <* %   M-000.125505  %  NMH1102 MESSAGE OUTPUT FILE ':MH20:$TSOS.SYSMES.BS2CP.210', 
                          ACCESS=DLAM + ISAM, ACTION=STARTUP
  <* %   M-000.125505  %  NMH1102 MESSAGE OUTPUT FILE ':MH20:$TSOS.SYSMES.EKP.01', ACCESS=ISAM, ACTION=STARTUP
  <* %   M-000.125505  %  NMH1112 MESSAGE PROCESSING READY
...
  <* %SERS-000.125515  %  NER1500 SERSLOG LOGGING FILE ':MH20:$TSOS.SYS.SERSLOG.2021-01-25.025.01' OPENED
  <H % TSC-000.125515  %  HEL0001 HW ERROR LOGGING FILE ':MH20:$TSOS.SYS.HEL.2020-11-28.154947' 
                          OPENED WITH 'SPACE=  402'
  <R % TSC-000.125515  %  EXC0040 LOGGING FILE ':MH20:$SYSAUDIT.SYS.REPLOG.2021-01-25.025.01' OPENED
...
  <@ %HT1C-000.125516  %  CMD0695 SYSTEM SYNTAX FILE ':MH20:$TSOS.SYSSDF.SDF.048' ACTIVATED
  <@ %HT1C-000.125516  %  CMD0695 SYSTEM SYNTAX FILE ':MH20:$TSOS.SYSSDF.ACS.210' ACTIVATED
...,
  <A % TSC-000.125522  %  NJA0001 D.E.R INITIALIZED SUCCESSFULLY
  <* % MSG-000.125522  %  ETMRK18 CPU 01 ATTACHED
  <* %ACCT-000.125522  %  NAM0001 NEW ACCOUNTING FILE ':MH20:$TSOS.SYS.ACCOUNT.2021-01-25.025.01' 
                          OPENED WITH 'SPACE=(48,48)'
  <* % DRV-000.125522  %  DRV1010 FILE ':MH20:$TSOS.SYSPAR.DRV.032' IS USED AS DRV CONFIGURATION FILE.
  <* % TSC-000.125522  %  NSI0000  ***  S Y S T E M   R E A D Y  *** 
----------------------------------------------------------------------------------------- 16.
  <J % TSC-000.125522  %  JMS0066 JOB 'JSTREAM' ACCEPTED ON 17-01-25 AT 12:55, TSN = 59Y2
  <R % TSC-000.125522  %  JMS0300 JOB STREAM '$SYSJS' 'ATTACHED'
  <J %59Y2-000.125522  %  JMS0154 'TSOS' LOGGED ON FOR 'NTL'. JOB NAME 'JSTREAM'. CALLER 'TSN  TSC'. TID 00020050
  <R %59Y2-000.125522  %  JMS0300 JOB STREAM 'JSTREAM' 'ATTACHED'
...
  <* %SEST-000.125522  %  NBR3000 SYSTEM EVENT STREAM FILE ':MH20:$SYSAUDIT.SYSLOG.ESS.SYSTEM' OPENED
OPRR /(C0)-000.125522 RUN CMDFILE 
----------------------------------------------------------------------------------------- 17.
  <* % UCO-000.125522  %  NBR0972 OPERATOR TASK WITH TSN 'XABY' CREATED FOR PROCESSING OF /RUN COMMAND SEQUENCES
(C0) +RUNT-000.125522  %  NBR1000 COMMAND '/RUN' RECEIVED. RUN ID '0001' ASSIGNED
(C0) +RUNT-000.125522  %  NBR1001 RUN ID '0001'. READING OF /RUN COMMAND FILE ':MH20:$TSOS.CMDFILE' STARTED
OPRR /(C0)-000.125522 DCSTART DCSOF=SOF.ABGSE211.SE
OPRR /(C0)-000.125522 START-SUBS CRTEBASY
OPRR /(C0)-000.125522 START-SUBS SPOOL
...

  1. DIALOG startup is to be performed without a special option (response: EOT).

  2. The home pubset is online.

  3. Date and time as per SVP are displayed

  4. The SYSSTART REP file is processed.

  5. The default startup parameter file should be processed (response: EOT).

  6. No other parameter files are to be processed (response: END).

  7. The file name for BS2000 should be entered. If the response is EOT, BS2000 is loaded from the default file.

  8. The response EOT causes the default REP file to be processed.

  9. No other REP files should be processed (response: END).

  10. Various items of system information are output: name and version of the operating system, time of generation, available memory space, time zone information, TODR epoch, configuration data, size of the paging areas.

  11. The paging section of the BS2000 execution section was successfully loaded and corrected (REP processing). It is thus ready for execution.

  12. The parameter records selected in (5) are logged in CONSLOG. Processing takes place at different times depending on the parameter keyword.

  13. The command file with the name specified by means of the system parameter CMDFILE is to be automatically processed after “System Ready” (response: EOT). If the response is N (DO NOT USE), a CMDFILE can subsequently be started with the RUN CMDFILE command.

  14. A cold start is to be performed (response: C).

  15. Catalog reconfiguration should be performed as defined in the parameter service (response: N). In this example, therefore, with RECONUC=N.

  16. “System Ready”, the BS2000 system is ready to operate.

  17. Automatic start of the command file CMDFILE (see (13)).

Powered by Atlassian Confluence and Scroll Viewport.