You use this command to output the basic structures of BCAM
DCMBASE |
*ALL [ CB = *NONE / *ALL / list-poss (6): BASETAB / BTSBTAB / BCAMCB / CMDCB / STATE / TASKCB ] [ ,LOG = *NONE / *ALL / list-poss (6): HERSLOG / SERSLOG / PERMTRACE / MEM-3-REL / MEM-5-REL / MEMO-CALL ] [ ,AREA = *NONE / *ALL / list-poss (8): YDBFST / STACK / KA-SLOT / STARTPAR / MEM-3 / MEM-5 / BCAT-SIGNAL / CONA-SIGNAL ] [ ,CMD = *NONE / *ALL / list-poss (6): / BCMOD / BCOPTION / BCSET / BCTIMES / MODIFY-BCAM-OPTIONS,[OPTION=...] / ,OPTION=*ALL / list-poss (14): LINE-OPTIONS / IP-RANGE / REMOTE-SERVER-PORTS / SERVER-PORTS / AUTOMATIC-ES-CREATE / MISCELLANEOUS / CMDFILE-PROCESSING / AVAILABILITY-OPTIONS / IP-OPTIONS / IPV6-OPTIONS / ISO-OPTIONS / SNMP-OPTIONS / DNS-OPTIONS MODIFY-DNS-ACCESS,[DNS-ACCESS=...]] DNS-ACCESS=... *ALL / list-poss(3): IP-ADDRESSES / IPV6-ADDRESSES / NAMES MODIFY-VLAN-ASSIGNMENT,[VLAN-ASSIGNMENT=...]] VLAN-ASSIGNMENT=... *ALL / list-poss(2): IP / IPV6 |
*ALL
All control blocks, logging information, and other areas are output.
CB=
Defines which control blocks are to be output.
Apart from the values *NONE and *ALL, the remaining values can also be specified as a list (list-poss).
*NONE
DCM base table, BTSBTAB, BCAMCB, and CMDCBs are not output.
*ALL
All control blocks, i.e. DCM base table, BTSBTAB, BCAMCB, and CMDCBs are output.
BASETAB
The DCM base table (YDYYBASE) is output.
BTSBTAB
The BTSBTAB is output.
BCAMCB
The BCAMCB is output.
CMDCB
CMDCBs are output.
STATE
The state of the data communication system is output in readable form.
TASKCB
The control blocks of transport task processes are output in readable form.
LOG=
Controls which logging information is to be output.
Apart from the values *NONE and *ALL, the remaining values can also be specified as a list (list-poss).
*NONE
HERS entries, SERS entries, and the permanent trace are not output.
*ALL
HERS entries, SERS entries, and the permanent trace are output.
HERSLOG
The HERSLOG entries are output.
SERSLOG
The SERSLOG entries are output.
PERMTRACE
The permanent trace is output.
MEM-3-REL
The release trace for ADM class-3 memory is output.
MEM-5-REL
The release trace for ADM class-5 memory is output.
MEMO-CALL
The trace on $GETMEM and $RETMEM by BCAM is output.
AREA=
Defines which (additional) areas are to be output.
Apart from the values *NONE and *ALL, the remaining values can also be specified as a list (list-poss).
*NONE
The SIH stack area, the Kernel Activity slots, and the start parameters are not output.
*ALL
The SIH stack area, the Kernel Activity slots, and the start parameters are output.
YDBFST
The SIH stack area is output.
STACK
The SIH stack area is output.
KA-SLOT
The Kernel Activity slots are output.
STARTPAR
The start parameters are output.
MEM-3
The ADM class-3 memory is output.
MEM-5
The ADM class-5 memory is output.
BCAT-SIGNAL
The BCAT-SIGNAL slot ranges are output.
CONA-SIGNAL
The CONA-SIGNAL slot ranges are output.
CMD=
Controls the BCAM parameters for which the generation commands are output. list-poss causes them to be output in list form. list-poss cannot be used for *NONE and *ALL.
*NONE
No generation commands are output.
*ALL
All available generation commands are output as a list.
BCMOD
The generating BCMOD commands are output.
BCOPTION
The generating BCOPTION commands are output for the BCAM operating options.
BCSET
The generating BCSET commands are output for the BCAM diagnostic parameters.
BCTIMES
The generating BCTIMES commands are output for the BCAM time intervals.
MODIFY-BCAM-OPTIONS,OPTION=...
The generating MODIFY-BCAM-OPTIONS commands or the corresponding BCOPTION commands are output for special BCAM commands.
OPTION=
Controls the BCAM options for which the generation commands are output. listposs causes them to be output in list form. list-poss cannot be used for *NONE and *ALL.
*ALL
All available generation commands are output as a list.
LINE-OPTIONS
Outputs the BCOPTION commands for all line options.
IP-RANGE
Outputs the BCOPTION commands for all IP-RANGE settings.
REMOTE-SERVER-PORTS
Outputs the BCOPTION commands for all REMOTE-SERVER-PORT settings.
SERVER-PORTS
Outputs the BCOPTION commands for all SERVER-PORT settings.
AUTOMATIC-ES-CREATE
Outputs the BCOPTION commands for all AUTOMATIC-ES-CREATE settings.
MISCELLANEOUS
Outputs the MODIFY-BCAM-OPTIONS commands for all MISCELLANEOUS options.
CMDFILE-PROCESSING
Outputs the MODIFY-BCAM-OPTIONS commands for all CMDFILE-PROCESSING options.
AVAILABILITY-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all AVAILABILITY-specific options.
IP-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all IP-specific options.
IPV6-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all IPv6-specific options.
ISO-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all ISO-specific options.
SNMP-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all SNMP-specific options.
DNS-OPTIONS
Outputs the MODIFY-BCAM-OPTIONS commands for all DNS-specific options.
MODIFY-DNS-ACCESS,DNS-ACCESS=...
Outputs the generating MODIFY-DNS-ACCESS commands for the BCAM-DNS access settings.
DNS-ACCESS=
Controls the BCAM-DNS access settings for which the generating commands are to be output.
list-poss causes them to be output in list form. list-poss cannot be used for *NONE and *ALL.
*ALL
Outputs all the available generation commands as a list.
IP-ADDRESSES
Outputs the MODIFY-DNS-ACCESS commands for all the BCAM-DNS-ACCESS settings which affect the IP addresses.
IPV6-ADDRESSES
Outputs the MODIFY-DNS-ACCESS commands for all the BCAM-DNS-ACCESS settings which affect the IPv6 addresses.
NAMES
Outputs the MODIFY-DNS-ACCESS commands for all the BCAM-DNS settings which affect the processor’s namespace.
MODIFY-VLAN-ASSIGNMENT,VLAN-ASSIGNMENT=...
Outputs the generating MODIFY-VLAN-ASSIGNMENT commands for the BCAM VLAN-ASSIGNMENT settings.
VLAN-ASSIGNMENT=
Controls the BCAM VLAN-ASSIGNMENT settings for which the generating commands are to be output.
list-poss causes them to be output in list form. list-poss cannot be used for *NONE and *ALL.
*ALL
Outputs all the available generation commands as a list.
IP
Outputs the MODIFY-VLAN-ASSIGNMENT comands for all the BCAM VLAN-ASSIGNMENT settings which affect the IP addresses.
IPV6
Outputs the MODIFY-VLAN-ASSIGNMENT comands for all the BCAM VLAN-ASSIGNMENT settings which affect the IPv6 addresses.