BFORMAT

2100	realmname IS TOO SMALL Meaning The realm cannot be formatted because it was configured too small and is not extensible. This does not, however, affect formatting of the other realms. Response Enlarge realmname to at least the size specified by BGSIA-ESTIMATE-REPORT or permit it to be extended by defining a secondary assignment > 0 and restart BFORMAT (possibly only for realmname).
2105	DATABASE DIRECTORY IS NOT RELIABLE Meaning During DBDIR processing by the DBH or by another UDS/SQL utility routine, an error occurred. The database is thus inconsistent and cannot be processed by BFORMAT. Response Determine cause of inconsistency, eliminate it and restart BFORMAT.
2108	realmname IS NOT PRESENT OR NOT WRITEABLE OR PASSWORD IS NOT SPECIFIED DMS-CODE = dmscode, FILE = realmname bzw. RET-CODE = retcode, FILE = realmname Meaning The indicated realm cannot be processed for one of the reasons listed. For details refer to the DMS code output subsequent to this message and the continuation lines. Response Determine cause, remove, and repeat BFORMAT call for the realm concerned. Possible continuation lines PASSWORD IS NOT SUPPLIED FILE IS NOT PRESENT FILE IS NOT SHAREABLE FILE IS EMPTY FILE IS NOT WRITEABLE FILE IS NOT EXISTING ACT_KEY_ZERO IS NOT CORRECT FILE EXISTS IN MORE THAN ONE PVS
2113	realmname IS NOT PRESENT Meaning The indicated realm does not exist or cannot be processed. Response Make realm available and restart BFORMAT for this realm.
2115	INPUT STATEMENT SYNTACTICALLY WRONG, PLEASE REPEAT STATEMENT Meaning The user entry does not begin with the keyword REALM or does not end with the keyword END. Entering END results in termination of BFORMAT in any event, correct input of the REALM statement results in continuation of the program run. Response Enter the correct statement, or END in order to terminate the BFORMAT run.
2116	WRONG NAME IN REALM LIST: realmname Meaning realmname is not contained in the schema and therefore cannot be processed. The database either does not contain a realm of this name or the SIA is erroneous. Response Correct entry depending on the cause of the error and restart BFORMAT for this realm.
2117	FOR DBDIR AI-LOGGING IS WANTED, BUT BFORMAT CAN NOT DO SO. SWITCH OFF AI-LOGGING BY INCREASING THE VERSION BEFORE RESTARTING BFORMAT. Meaning AFIM logging was activated for the database. Since BFORMAT does not perform logging, this run is aborted. Response Logging must be switched off by means of BMEND. Restart of BFORMAT can then be effected using the same entry.
4111	CATALOG-FILE HAS NOT BEEN FORMATTED OR COULD NOT BE READ Meaning The dbname.CATALOG file of the database cannot be processed, i.e. BCREATE was not performed for the database. Response Increase size of dbname.CATALOG file, if necessary, and recreate the database by means of BCREATE.
4120	SPECIFIED PAGE SIZE FOR DATABASE REALMS IS NOT ALLOWED Meaning The specified DB page size is not permissible. Response Specify permissible page size (DATABASE-PAGE-LENGTH) or generate diagnostic documentation and write error report.
7100	OPERATION = operation, AREA-REF = realmref RETCODE = retcode, ACT-KEY = last-page-number Meaning An error, the cause of which cannot be determined, occurred in the operation module when processing the realm realmref. If there is a DMS code, it is output subsequent to this message. Response If the error is a read/write error, BFORMAT must be restarted. If the error recurs, prepare an error report with runtime log and dump.
9110	operation - ERROR, RETCODE = retcode, DMS-CODE = dmscode, [FILE = filename] Meaning Read/write error. Response If the error is a read/write error, BFORMAT must be restarted. If the error recurs, prepare an error report with runtime log and dump.
9112	FSTAT-ERROR DMS-CODE = dmscode ERRORBYTE = errbyte FILE = filename
	Meaning A runtime error occurred when an SHOW-FILE-ATTRIBUTES command pertaining to the indicated file was executed. The message is followed by a dump of the parameter block of the SHOW-FILE-ATTRIBUTES command for diagnostic purposes. Response Write error report and include runtime log as well as documentation on the file in question.
9120	operation - ERROR, RETCODE = retcode, DMS-CODE = dmscode, FILENAME = filename, BNR = page-number Meaning Read/write error on processing the indicated file at the corresponding page number. Response If the error is a read/write error, BFORMAT must be restarted. If the error recurs, prepare an error report with runtime log and dump.
9130	operation - ERROR, RETCODE = retcode, DMS-CODE = dmscode, FILENAME = filename, BNR = page-number Meaning Read/write error on processing the indicated file at the corresponding page number. Response If the error is a read/write error, BFORMAT must be restarted. If the error recurs, prepare an error report with runtime log and dump.
9131	WRITLES-ERROR, NUMBER OF BLOCKS TO WRITE = number < = O Meaning Error occurred when writing DBTTs and CALC tables. Response Generate diagnostic documentation and write error report.