Messages of the UTM tool KDCDUMP

K700	KDCDUMP &VERS started.
K701	Difference between the number of existing UTM tables and the number of UTM tables which are known by KDCDUMP. UTM area(s): &UTMA1&UTMA2&UTMA3&UTMA4&UTMA5&UTMA6&UTMA7
K702	Abnormal end
K703	Term application reason &TRMA
K704	Table entry index not valid.
K705	UTM dump &FNAM or part of it read in memory.
K706	This type of preparation is not allowed for table &TABNAM.
K707	Error on calling EDT. EDT call : &EDTINT Return code: &EDTRET This message is issued when EDT reports an error. The insert EDTINT shows which subprogram interface of EDT reported the error (INF=IEDTINF or CMD = IEDTCMD). The insert EDTRET contains the EDT return code in the following sequence: subreturn code 1 (1 byte), sub-return code 2 (1 byte), main return code (2 bytes). Refer to the EDT documentation for a description of the return codes.
K708	EDT version not supported by KDCDUMP. EDT version: &EDTVER
K709	Only one entry of a slot table can be prepared.
K710	Error on command
K711	No UTM dump in memory.
K712	Requested address X'&SADDR' not in present UTM dump or selected domain.
K713	Requested address X'&SADDR' is present in table &TABNAM, but not within one table entry.
K714	Error on link &LNAM: DMS return code &DMSE.
K716	Open error on file &FNAM. DMS return code : &DMSE.
K717	Request memory error
K718	File &FNAM does not contain a UTM dump.
K719	KDCDUMP &VER1 cannot prepare a UTM dump &VER3.
K720	Only the directory of the UTM dump exists.
K721	&UTMA1 is not present in UTM-dump or in selected domain.
K722	&NUM1 bourse cycle with the criterias CREF=&CREF and ANNO=&ANNO1 is found.
K723	Write error on file &FNAM. DMS return code: &DMSE.
K724	Command not allowed at present time.
K725	Table index is too low or too high.
K726	Address is too low or too high.
K727	FSTAT: Error on file &FNAM. DMS return code: &DMSE.
K728	Normal end
K729	Output file &FNAM is written.
K730	Read error on file &FNAM. DMS return code: &DMSE.
K731	The name &DEFTYPE is not a valid UTM type.
K732	UTM dump does not contain UTM type &DEFTYPE.
K733	Table name &TABNAM does not exist.
K734	The UTM dump &FNAM could not be written completely. Last written UTM area is &UTMA1. This message indicates that the UTM dump could not be written completely. There may have been insufficient space available for the User-Id. The UTM areas are dumped in the following order: KAA, SLOT, CACHE, MPGP, XAPTP-GLOBAL, KTA, XAPTP-LOCAL, STACK, ROOT, REP.  In the case of a PENDER dump, only ROOT  dumped. The individual tables for the UTM areas can be output by means of the KDCDUMP statement HELP TABLE-NAMES ("HELP Help about KDCDUMP"); they appear in the dump order. The XAPTP sections form a block.
K735	Table &TABNAM does not exist in UTM dump or in selected domain.
K736	Index out of range - index is set to lowest or highest allowed table index.
K737	End-index lower than start-index - end-index is given the value of the start-index.
K738	No REP file is contained in UTM dump.
K739	No REP records ( PM-NO: &PMNO ) found.
K740	Abbreviation of table name ambiguous with regard to &TABNAM &TABNAM1 &TABNAM2 &TABNAM3 &TABNAM4 &TABNAM5.
K741	Information not available. Table name: &TABNAM This message indicates that a UTM area or a table could not be dumped by the UTM dump creator because the area or the table was not fully accessible.
K742	The KDCDUMP version on the hardware &HW1 with &OS1 as operating system cannot read a UTM dump written on the hardware &HW2 with the operating system &OS2.
K743	For the table &TABNAM no displacement is possible.
K744	Offset lower than 0 or higher than the no. of bytes for one table entry.

K745	No symbolic preparation for this table &TABNAM possible.
K746	Error on symbolic preparation.
K747	Command has no result.
K753	The name &FIRES is not a UTM resource of UTM type &DEFTYPE.
K754	No further entry with this UTM type in this dictionary table.
K755	Input error: No further command can be read.
K756	False value for DB operand. Only &DBMAX database(s) are generated.
K757	The version of &UTMA1 (&VER1) is not compatible with the version of KDCDUMP ( &VER2 ).
K758	No summary was written.
K759	Input string is longer than the permitted length (256 char).
K760	No entry with the name &FIRES found.
K761	No further entry with the name &FIRES found.
K770	Error detect while checking compression of file &FNAM. Error code: &ERRC.
K771	Error detect while creating temporary file for &FNAM. Error code: &ERRC.
K772	Error detect while decompressing file &FNAM. Error code: &ERRC.
K773	Requested information can not be found in the selected domain.
K774	Requested domain for command SFIND not read from dump file. Recommendation: Read domain with FILE=<dumpfile>,DOMAIN=<domain> and repeat SFIND command.
K780	No dump file was closed.
K781	Compressed dump file could not be uncompressed.
K782	No hit found.
K783	Value of HITS is neither ALL nor between 0 and 32767.
K784	Size of address greater than 32 bit is forbidden.